Valves

The Ridart anti-syphon (pressure regulating) valves cope with higher fuel dispensing pump flow rates of up to 200 litres per minute. Fully adjustable depending on the height of the tank/head pressure of fuel, this anti-syphon (pressure regulating) valve ensures the dispensing pumps are not being overworked and prevents fuel from coming out of the pump unit air separator outlet valve. It helps to prevent fuel loss and fuel contamination. This anti-syphon (pressure regulating) valve is easy to install as it comes with 1½" female BSPT flanged inlet and outlet ports.

This Brass Check Valve is a spring loaded valve for use in pipe systems where flow is required in one direction and no return flow is allowed. These check valves can be installed in any orientation and are fitted with Female BSP threads.

This Stainless Steel Solenoid Valve is a direct acting valve, meaning that no pressure has to be applied to operate, suitable for a range of fluids including AdBlue™, fuels, oil and water. As a normally closed solenoid valve, the liquid flow is shut off until the valve is activated. When the coil integral to the valve becomes energised by an electrical current, the valve opens to enable the flow of liquid through the pipeline.

This stainless steel solenoid valve is therefore designed for situations where the fluid only needs to be released at certain intervals, for example to feed a generator with fuel from the back up storage tank. The valve could also be wired into a pump to make sure that fluid only enters the pipework from the tank when the pump is activated.

This Brass Solenoid Valve is a direct acting valve, meaning that no pressure needs to be applied to operate, for a range of fluids including fuels, oils and water. As a normally closed solenoid valve, until the valve is activated the fluid flow is shut off. When the electrical current that runs through the coil inside the valve is energised, the valve opens and allows the flow of liquid through the pipework.

This brass solenoid valve is therefore designed for applications where fluid only needs to be released on occasions, such as to feed a generator with diesel from the back up storage tank. It could also be wired into a pump ensuring that fuel only enters the pipework from the tank when the pump is turned on.

The Locking Angle Brass Gate Valve is used primarily on the bottom outlet of a gravity fed diesel storage tank. These gate valves are designed to come out at 90º to take away the pressure on the hose, and to maximize the flow rate through the delivery hose without restriction.

The locking lever on these gate valves allows it to be padlocked when not in use. This angle gate valve is supplied as standard on some of our Gravity Hose Kits.

The Brass Gate Valve is a standard gate valve which can be used for a variety of applications, including on some of our Gravity Hose Kits. These gate valves are designed for starting/shutting off flow. The gate valves are used within fuel and water installations, and are suitable for use with diesel, oil and water.

Brass Body & Bonnet, Cast Handwheel, Screwed BSPT. PN20 rating, Temperature -20°C to 120°C.

The Stainless Steel Lockable Lever Ball Valve is designed for applications where brass is not suitable. This version of ball valve is therefore used for installations with more aggressive fluids such as AdBlue™ and chemical fluid pipelines. The lockable lever ball valves can be locked using a padlock in either the open or closed position, and the locking device covers the stem nut, which means that if the padlock is on, the lever is impossible to remove.

This valve us fatted with an Anti-blowout stem and PTFE seals. PN63 Rating, Temperature -10°C to 180°C.

The Brass Lockable Lever Ball Valve is designed for a variety of applications and is available in a range of sizes. These lockable brass ball valves include a locking mechanism meaning that these are often required for security or safety. The lever ball valves can be locked using a padlock in either the open or closed position, and the locking device covers the stem nut, which makes the removal of the lever impossible without first removing the padlock.

The Brass Angle Ball Valve is a nickel plated 90° full bore brass ball valve that meets EN331  standards. These angle ball valves are rated PN40 and are suitable in temperatures between -20°c - + 110°c.

The Brass Compression Lever Ball Valves are designed for starting/shutting off flow and come in a range of sizes. These nickel-plated full bore brass ball valves have a steel handle, NBR o-ring and PTFE seals and come with heavy duty industrial brass olives. These lever ball valves are WRAS and EN331:1998 gas approved and are a popular choice within heating and plumbing applications.

The Red Handle Lever Ball Valve is a nickel-plated full bore brass ball valve popular in fuel, plumbing, heating & waterworks applications. Designed for starting/shutting off flow, these lever ball valves have a PVC coated steel handle, PTFE seats and an anti-blowout stem.

Rated PN32 ¼” to 1”, PN25 1¼” to 2”, PN30 2½” & 4”, Temperature 0°C to 90°C.

The Yellow Handle Lever Ball Valve is a nickel-plated full bore brass valve popular within gas, water and fuel applications and comes in a range of sizes. These lever ball valves are WRAS and EN331:1998 gas approved, have a steel handle, NBR o-ring and PTFE seals, and come in two different pressure ratings depending upon the size of the valve.